सॉफ्टवेयर और फर्मवेयर अभिलेखागार

Initial release

Initial release

Initial release

New Feature

• Initial release

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

IMPROVEMENT

• Added new frequency band Z14 (1910-1920 MHz) for Brazil

KNOWN ISSUES

• If the SCM820 automatic mixer is selected as the Audio Output Device for automatic routing of APT audio channels, ensure that the SCM820 firmware version is higher than version 1.2.3. Alternatively, use Dante Controller software to route the channels. For a free Dante routing and diagnostic tool, see Audinate.com.
• Transmitters may fail to update if they are on a firmware version that is lower than the firmware version on the charger that they are docked on. To properly update transmitters, ensure transmitters are docked on chargers with firmware version 4.0.6.

NOTES

• For operation of MXW devices with other Shure networked systems, see the following list of minimum software and firmware versions that are supported with MXW version 4.0.6:
  • SCM820 1.2.3
  • Shure Web Device Discovery 1.0.17
  • Shure Update Utility 2.2.2.8
• Dante Packet Bridge Support: A third-party Dante device (e.g. a Dante DSP) used with the MXWAPT can now obtain the MXWAPT Control IP Address through a data channel on the Dante Network, allowing greater flexibility in network architecture and setup with multiple interfaces. Seewww.shure.com/faq and search on 'packet bridge'.

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

IMPROVEMENT

• Added new frequency band Z14 (1910-1920 MHz) for Brazil

KNOWN ISSUES

• If the SCM820 automatic mixer is selected as the Audio Output Device for automatic routing of APT audio channels, ensure that the SCM820 firmware version is higher than version 1.2.3. Alternatively, use Dante Controller software to route the channels. For a free Dante routing and diagnostic tool, see Audinate.com.
• Transmitters may fail to update if they are on a firmware version that is lower than the firmware version on the charger that they are docked on. To properly update transmitters, ensure transmitters are docked on chargers with firmware version 4.0.6.

NOTES

• For operation of MXW devices with other Shure networked systems, see the following list of minimum software and firmware versions that are supported with MXW version 4.0.6:
  • SCM820 1.2.3
  • Shure Web Device Discovery 1.0.17
  • Shure Update Utility 2.2.2.8
• Dante Packet Bridge Support: A third-party Dante device (e.g. a Dante DSP) used with the MXWAPT can now obtain the MXWAPT Control IP Address through a data channel on the Dante Network, allowing greater flexibility in network architecture and setup with multiple interfaces. Seewww.shure.com/faq and search on 'packet bridge'.

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

IMPROVEMENT

• Added new frequency band Z14 (1910-1920 MHz) for Brazil

KNOWN ISSUES

• If the SCM820 automatic mixer is selected as the Audio Output Device for automatic routing of APT audio channels, ensure that the SCM820 firmware version is higher than version 1.2.3. Alternatively, use Dante Controller software to route the channels. For a free Dante routing and diagnostic tool, see Audinate.com.
• Transmitters may fail to update if they are on a firmware version that is lower than the firmware version on the charger that they are docked on. To properly update transmitters, ensure transmitters are docked on chargers with firmware version 4.0.6.

NOTES

• For operation of MXW devices with other Shure networked systems, see the following list of minimum software and firmware versions that are supported with MXW version 4.0.6:
  • SCM820 1.2.3
  • Shure Web Device Discovery 1.0.17
  • Shure Update Utility 2.2.2.8
• Dante Packet Bridge Support: A third-party Dante device (e.g. a Dante DSP) used with the MXWAPT can now obtain the MXWAPT Control IP Address through a data channel on the Dante Network, allowing greater flexibility in network architecture and setup with multiple interfaces. Seewww.shure.com/faq and search on 'packet bridge'.

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

IMPROVEMENT

• Added new frequency band Z14 (1910-1920 MHz) for Brazil

KNOWN ISSUES

• If the SCM820 automatic mixer is selected as the Audio Output Device for automatic routing of APT audio channels, ensure that the SCM820 firmware version is higher than version 1.2.3. Alternatively, use Dante Controller software to route the channels. For a free Dante routing and diagnostic tool, see Audinate.com.
• Transmitters may fail to update if they are on a firmware version that is lower than the firmware version on the charger that they are docked on. To properly update transmitters, ensure transmitters are docked on chargers with firmware version 4.0.6.

NOTES

• For operation of MXW devices with other Shure networked systems, see the following list of minimum software and firmware versions that are supported with MXW version 4.0.6:
  • SCM820 1.2.3
  • Shure Web Device Discovery 1.0.17
  • Shure Update Utility 2.2.2.8
• Dante Packet Bridge Support: A third-party Dante device (e.g. a Dante DSP) used with the MXWAPT can now obtain the MXWAPT Control IP Address through a data channel on the Dante Network, allowing greater flexibility in network architecture and setup with multiple interfaces. Seewww.shure.com/faq and search on 'packet bridge'.

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

IMPROVEMENT

• Added new frequency band Z14 (1910-1920 MHz) for Brazil

KNOWN ISSUES

• If the SCM820 automatic mixer is selected as the Audio Output Device for automatic routing of APT audio channels, ensure that the SCM820 firmware version is higher than version 1.2.3. Alternatively, use Dante Controller software to route the channels. For a free Dante routing and diagnostic tool, see Audinate.com.
• Transmitters may fail to update if they are on a firmware version that is lower than the firmware version on the charger that they are docked on. To properly update transmitters, ensure transmitters are docked on chargers with firmware version 4.0.6.

NOTES

• For operation of MXW devices with other Shure networked systems, see the following list of minimum software and firmware versions that are supported with MXW version 4.0.6:
  • SCM820 1.2.3
  • Shure Web Device Discovery 1.0.17
  • Shure Update Utility 2.2.2.8
• Dante Packet Bridge Support: A third-party Dante device (e.g. a Dante DSP) used with the MXWAPT can now obtain the MXWAPT Control IP Address through a data channel on the Dante Network, allowing greater flexibility in network architecture and setup with multiple interfaces. See www.shure.com/faq and search on 'packet bridge'.

These release notes cover the following models:

• MXWNCS2/4/8 Networked Chargers
• MXWANI4/8 Audio Network Interfaces
• MXWAPT2/4/8 Access Point Transceivers
• MXW1/2/6/8 Wireless Microphones

IMPROVEMENT

• Added new frequency band Z14 (1910-1920 MHz) for Brazil

KNOWN ISSUES

• If the SCM820 automatic mixer is selected as the Audio Output Device for automatic routing of APT audio channels, ensure that the SCM820 firmware version is higher than version 1.2.3. Alternatively, use Dante Controller software to route the channels. For a free Dante routing and diagnostic tool, see Audinate.com.
• Transmitters may fail to update if they are on a firmware version that is lower than the firmware version on the charger that they are docked on. To properly update transmitters, ensure transmitters are docked on chargers with firmware version 4.0.6.

NOTES

• For operation of MXW devices with other Shure networked systems, see the following list of minimum software and firmware versions that are supported with MXW version 4.0.6:
  • SCM820 1.2.3
  • Shure Web Device Discovery 1.0.17
  • Shure Update Utility 2.2.2.8
• Dante Packet Bridge Support: A third-party Dante device (e.g. a Dante DSP) used with the MXWAPT can now obtain the MXWAPT Control IP Address through a data channel on the Dante Network, allowing greater flexibility in network architecture and setup with multiple interfaces. Seewww.shure.com/faq and search on 'packet bridge'.