Archiwum oprogramowania i firmware

Recommendation

• Update all ADPSM devices in a configuration to the same firmware version.

Notes

• User Guide
• To operate this version of ADPSM with other Shure systems and software, see the following list of recommended versions:
  • AD600 1.1.7
  • AD610 1.4.33
  • Shure Update Utility 2.8.7
  • Wireless Workbench 7.4.0

Initial Release

Recommendation

• A new firmware version was released. It is highly recommended to update all Axient Digital PSM devices to version 1.0.23 or later. 

Known Issues

• With larger numbers of ShowLink connected ADXR devices, it may take more time for the ADXR to appear online.
• In some cases, ADXR can lose ShowLink connectivity. Power cycling the ADXR resolves the issue. 
• On rare occasions, power cycling the transmitter with larger numbers of ShowLink connected ADXR devices cause a few of the connected ADXR units to crash.
• Utilizing the maximum 64 Cue Entries cause slowness when accessing other features, such as Spectrum Scan. On rare occasions, this may lead to a crash, which requires removing and reinserting the battery to recover.
• Auto Off feature inside the Utilities menu does not deliver any functionality since the Power Save feature is not yet available. 
• MixMode balance does not restore back to L=R after a factory reset. 
• Battery error occurs when docking ADXR into the SBC441 charger under the following conditions: 1) The ADXR power switch position is set to ON. 2) The ADXR is docked with a depleted SB910 rechargeable battery. Undocking the ADXR and setting the power switch position to OFF and docking the ADXR back into the charger will resolve the issue. 

Notes

• User Guide
• To operate this version of ADPSM with other Shure systems and software, see the following list of recommended versions:
  • AD600 1.1.7
  • AD610 1.4.33
  • Shure Update Utility 2.8.7
  • Wireless Workbench 7.4.0

Recommendation

• Update all ADPSM devices in a configuration to the same firmware version.

New Features

• Monitor and Control unlinked ADXR devices – When setting the ADXR bodypack receiver and AD610 wireless access point to the same ShowLink network ID, users can monitor and control unlinked ADXR devices. 
• ShowLink Netwok ID – Under the Utilities menu, select ShowLink Netwok ID to set a 4-digit code that matches with AD610 wireless access points in your ShowLink network. This allows all linked and unlinked ADXR devices on the network. With ShowLink Network ID, users can now perform sync interactions over ShowLink instead of IR sync. 
• Power Save – To extend battery life, users can enable Power Save mode, which powers down audio and RF sections after 5 minutes of the ADXR powered on without a connected headphone. Entering and exiting power save mode requires the ADXR to reboot. 

Improvements

• Improved stability of ShowLink connectivity
• Improved limiter behavior for the ADXR headphone output
• Fixed issue that caused a battery error when docking ADXR into the SBC441 charger with a depleted SB910 battery and/or docking the ADXR with the power switch position set to OFF.

Known Issues

• When updating firmware via ShowLink, the firmware update may occasionally fail, which may require users to pull the battery to power cycle the unit and restart the firmware update. 
• MixMode balance does not restore back to L=R after a factory reset. 

Notes

• User Guide
• To operate this version of ADPSM with other Shure systems and software, see the following list of recommended versions:
  • AD600 1.1.7
  • AD610 1.4.33
  • Shure Update Utility 2.8.7
  • Wireless Workbench 7.4.0

Initial Release

Recommendation

• A new firmware version was released. It is highly recommended to update all Axient Digital PSM devices to version 1.0.23 or later. 

Notes

• User Guide
• To operate this version of ADPSM with other Shure systems and software, see the following list of recommended versions:
  • AD600 1.1.7
  • AD610 1.4.33
  • Shure Update Utility 2.8.7
  • Wireless Workbench 7.4.0

Recommendation

• Update all ADPSM devices in a configuration to the same firmware version.

Notes

• User Guide
• To operate this version of ADPSM with other Shure systems and software, see the following list of recommended versions:
  • AD600 1.1.7
  • AD610 1.4.33
  • Shure Update Utility 2.8.7
  • Wireless Workbench 7.4.0

Initial Release

Notes

• User Guide
• Firmware updates for MV7i are available in the MOTIV Mix desktop application

Compatibility

• MV7i is compatible with the following software versions:
  • MOTIV Mix 1.4.0
  • MOTIV Audio 4.5.0
  • MOTIV Video 2.5.0

Improvements

• Bug fixes

Known Issues

• The app can play files that are stored in the device’s music library. To enable this, go to the iOS Settings app, select PLAY from the list of apps, and turn on the “Allow PLAY to access Media & Apple Music” setting.
• The app only plays files that are stored locally on the device. Some tracks that are stored in the cloud may appear grayed out in the app, but they cannot be played.

Notes

• User Guide
• Please report problems and submit general feedback in the app settings page

Compatibility

• This app is compatible with iOS 17 or later. We can’t ensure compatibility or full-feature functionality with older operating systems.