ULXD4 - 900 MHz ISM Digital Wireless Receiver

Improvements

• Support for added hardware revisions

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Known Issues

• Group Scan Deployment and Custom Group Load may not work with other ULXD4/ULXD4D/ ULXD4Q that are running older firmware versions

Notes

• User Guides: ULXD4 | ULXD4D/Q
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate this version of ULX-D devices with other Shure networked systems and software, see the following list of recommended versions:
  • ULXD 2.8.6
  • Axient AXT600 Spectrum Manager 2.1.41
  • SBC250/450/850 Networked Charging Stations 2.8.6
  • Shure Update Utility 2.8.3
  • ShurePlus Channels iOS 1.6.1
  • ShurePlus Channels Android 1.6.2
  • Wireless Workbench 6.15.4 or 7.0.0

Improvements

• Fixed distorted audio issue on ULXD4 devices with Dante version REV3
• Fixed issue where ULXD4 devices sometimes disappear from Wireless Workbench® and do not reconnect

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Known Issues

• Group Scan Deployment and Custom Group Load may not work with other ULXD4/ULXD4D/ ULXD4Q that are running older firmware versions

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate this version of ULX-D devices with other Shure networked systems and software, see the following list of recommended versions:
  • ULXD1/2/6/8 Transmitters 2.7.3
  • ULXD4/4D/4Q Receivers 2.7.6
  • Axient AXT600 Spectrum Manager 2.1.41
  • SBC250/450/850 Networked Charging Stations 2.7.3
  • Shure Update Utility 2.8.0
  • ShurePlus Channels iOS 1.6.0
  • ShurePlus Channels Android 1.6.0
  • Wireless Workbench 6.15.3

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Known Issues

• Group Scan Deployment and Custom Group Load may not work with other ULXD4/ULXD4D/ ULXD4Q that are running older firmware versions

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate this version of ULX-D devices with other Shure networked systems and software, see the following list of recommended versions:
  • ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.7.3
  • Axient AXT600 Spectrum Manager 2.1.41
  • SBC250/450/850 Networked Charging Stations 2.7.3
  • Shure Update Utility 2.7.2
  • ShurePlus Channels iOS 1.5.2
  • ShurePlus Channels Android 1.1.1
  • Wireless Workbench 6.15.0

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvements

• Support for added hardware revisions

Known Issues

• Group Scan Deployment and Custom Group Load may not work with other ULXD4/ULXD4D/ ULXD4Q that are running older firmware versions

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate this version of ULX-D devices with other Shure networked systems and software, see the following list of recommended versions:
  • ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.6.3
  • SBC250/450/850 Networked Charging Stations 2.6.3
  • Axient AXT600 Spectrum Manager 2.1.38
  • Wireless Workbench 6.15.0
  • ShurePlus Channels iOS 1.5.2
  • ShurePlus Channels Android 1.1.1
  • Shure Update Utility 2.7.1

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvements

• NEW TCPI commands for ULXD4/ULXD4D/ULXD4Q:
  • MODEL - Name of the receiver model
  • TX_FW - Firmware version of the received transmitter
• Support added for new ULXD4D/Q devices which ensure that encryption is used
  • At this time, AXT600 Spectrum Manager does not support always encryption DCID

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.5.0 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.5.0
  • SBC250/450/850 Networked Charging Stations 2.4.13
  • Axient AXT600 Spectrum Manager 2.1.38
  • Wireless Workbench 6.14.1
  • Shure Update Utility 2.6.1
  • ShurePlus Channels 1.4.6

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvements

• Changed the default RF band from AB to JB for ULXD4=-AB receivers
• Add support for China 470 MHz – 510 MHz frequency band (G53)

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  • Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  • Align the infrared ports with the transmitter
  • Press ENTER
• To operate ULX-D version 2.3.25 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.3.25
  • SBC250/450/850 Networked Charging Stations 2.4.9
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.3.24
  • PSM1000 1.7.10
  • Axient AXT600 Spectrum Manager 2.1.31
  • Wireless Workbench 6.14.0
  • Shure Update Utility 2.5.1
  • ShurePlus Channels 1.4.5

New Features

• Dante ™ update to software version 4.2.1.1 and firmware version 4.0.2.9

Improvements

• The lock setting for the front panel SCAN button now prevents frequency changes due to group scans initiated by other ULXD4 units
• Support for additional RF bands:
  • Thailand 694 – 703 MHz frequency band (M19)
  • Thailand 748 – 758 MHz frequency band (Q12)
• Bug fixes

Notes

• User Guide
• To operate ULX-D version 2.4.9 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.4.9
  • SBC250/450/850 Networked Charging Stations 2.3.6
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.3.8
  • PSM1000 1.6.21
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench 6.13.1
  • Shure Update Utility 2.4.6
  • ShurePlus Channels 1.4.2

Important

• New hardware revisions with the ULX-D 2.3.34 firmware version cannot be downgraded to previous firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvement

• Updated the firmware version number for the purpose of keeping all ULX-D firmware version numbers aligned for brand-new system installations.

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.3.34 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.3.34
  • SBC250/450/850 Networked Charging Stations 2.3.6
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.3.8
  • PSM1000 1.6.21
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench 6.12.6
  • Shure Update Utility 2.4.4
  • ShurePlus Channels 1.4.2

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvement

• Support for Thailand 174 – 210 MHz frequency band (V52)
• Added separate locks for group scan and transmitter sync

Known Issues

• New hardware revisions of ULX-D version 2.3.21 are not compatible with SystemOn 2.0-3.0.1.
• ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1.

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.3.21 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.3.21
  • SBC250/450/850 Networked Charging Stations 2.3.6
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
  • PSM1000 1.6.21
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench 6.12.6
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvement

• Support new hardware revisions of ULX-D. New revisions can't be downgraded below version 2.3.4.

Known Issues

• New hardware revisions of ULX-D version 2.3.4 are not compatible with SystemOn 2.0-3.0.1.
• ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1.

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D version 2.3.4 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.3.4
  • SBC250/450/850 Networked Charging Stations 2.3.4
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
  • PSM1000 1.6.19
  • Axient AXT600 Spectrum Manager 2.1.22
  • Wireless Workbench 6.12.6
  • Shure Update Utility 2.4.3
  • ShurePlus Channels 1.4.2

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvements

• Support for new frequency bands:
  • U.S. 572 – 616 MHz (J50A)
  • U.S. 653 – 663 MHz (L50A)
• Added power supply fail-safe protection
• Bug fixes

Known Issue

• ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1

Notes

• User Guide
• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• SystemOn 3.0.1 displays "Check system requirements, your current firmware version may not be confirmed compatible" for ULX-D version 2.2.24; however only ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 3.0.1.
• To operate ULX-D version 2.2.24 devices with other Shure networked systems and software, see the following list of minimum versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.2.24
  • SBC250/450/850 Networked Charging Stations 2.2.24
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
  • PSM1000 1.5.12
  • Axient AXT600 Spectrum Manager 2.1.11
  • Wireless Workbench 6.12.4
  • Shure Update Utility 2.4.2
  • ShurePlus Channels 1.4.1
  • SystemOn 3.0.1

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvements

• Compatibility with new products:
  • ULXD6 Wireless Boundary Microphone Transmitter
  • ULXD8 Wireless Gooseneck Base Transmitter
  • SBC450 4-Bay Networked Charging Station
  • SBC850 8-Bay Networked Charging Station
• New TPCI commands for charging stations, receivers, and transmitters
• Bug fixes
  • Custom groups for AB/JB bands now correctly transfer via IR sync
  • Antenna power alert will persist until it is cleared
  • Fixed a sporadic issue of transmitter firmware updates failing

Known Issue

• ULX-D version 2.1.16 is not compatible with SystemOn 2.1

Notes

• ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER
• To operate ULX-D devices on version 2.1.16 with other Shure networked systems and software, see the following list of minimum software versions:
  • ULX-D ULXD1/2/6/8 Transmitters and ULXD4, ULXD4D, ULXD4Q Receivers 2.1.16
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.1.5
  • SBC450/850 Networked Charging Stations 2.1.16
  • Wireless Workbench 6.12.1
  • Shure Update Utility 2.3
  • ShurePlus Channels 1.3.1

Important

• ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvements

• Improved large-scale network stability: In some cases of very large installations with earlier firmware versions, units occasionally would drop off the network and not be visible via WWB6 or other remote networking access. Version 2.0.28 resolves the issue and increases overall network stability.
• Added new frequency bands:
  • Europe: Z17: 1492 – 1525 MHz
  • Europe: Z18: 1785 – 1805 MHz
  • Australia: Z19: 1785 – 1800 MHz
  • Taiwan
    • Z20: 1790 – 1805 MHz
    • G62: 510 – 530 MHz
• Bug fixes

Notes

• Update all transmitters used with receivers via IR. After the receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER.
• For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 2.0.28:
  • ULX-D ULXD1/2 Transmitters and ULXD4, ULXD4D, ULXD4Q Receivers 2.0.28
  • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.0.16
  • Wireless Workbench 6.12
  • Shure Update Utility 2.2.2.8
  • ShurePlus Channels 1.3
• ULX-D 2.0.19 (release date: 9/16/2016) is no longer available in the firmware library. Release notes remain available for reference:
  • New Features
    • Support for Access Control, which allows users to specify PINs for networked devices to restrict access to them from unauthenticated Shure control software.
    • AMX/Crestron control string to get the ULXD firmware version.
      • Command: < GET FW_VER >
    • Ability to reverse polarity on ULXD1 and ULXD1LEMO3 bodypacks. To reverse polarity, use these options:
      • Bodypack Utilities menu: UTILITY > POLARITY
      • Save the IR preset on the receiver and then IR sync to the bodypack to incorporate the polarity change: IR PRESETS > BP POLARITY
  • Improvements
    • Added new VHF frequency bands:
      • V50
      • V51
    • Dante™ update to software version 3.9.6.1 and firmware version 4.0.0.6
    • Improved audio stability in marginal RF conditions
  • Known Issues
    • ShurePlus Channels version 1.2 does not support ULX-D firmware version 2.0 or later.
    • QLX-D firmware version 1.1.15 or earlier does not support ULX-D firmware version 2.0 or later.
  • Notes
    • Users must update all transmitters used with receivers via IR. After the receiver is updated, follow these steps:
      1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
      2. Align the infrared ports with the transmitter
      3. Press ENTER.
    • For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 2.0.19:
      • ULX-D ULXD1/2 Transmitters and ULXD4, ULXD4D, ULXD4Q Receivers 2.0.19
      • Wireless Workbench 6.12
      • Shure Update Utility 2.2.2.8

Improvement

• Added new frequency band Z16 (1240 – 1260 MHz) for Japan

Notes

• Fixed bug relating to encryption mismatch conditions.
• Fixed IR LED behavior when firmware updating transmitters.
• Transmitters to be used with receivers must be updated via IR. After the receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER.
• For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 1.7.34:
  • QLX-D receiver 1.0.15

New Feature

• ULXD4, ULXD4D, and ULXD4Q receivers can now power two UA864 antennas in parallel per receiver input for a total of four antennas. To view an example of a similar setup, with different antennas, see the FAQ: Antenna Distribution – 2 Rooms, 4 Antennas, which also includes information on how to modify the UA221 passive antenna accessory.

Notes

• Transmitters to be used with receivers must be updated via IR. After the receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER.
• For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 1.6.11:
  • QLX-D receiver 1.0.15

Improvements

• Added new frequency bands:
  • Americas (except Brazil): X52: 902-928 MHz
  • Brazil: X53: 902-907.5, 915-928 MHz
  • Australia: X54: 915-928 MHz

Notes

• Transmitters to be used with receivers must be updated via IR. After the receiver is updated, follow these steps:
  1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
  2. Align the infrared ports with the transmitter
  3. Press ENTER.
• For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 1.6.10:
  • QLX-D receiver 1.0.15