डाउनलोड

सॉफ्टवेयर और फर्मवेयर अभिलेखागार

अद्यतन प्रकार द्वारा फ़िल्टर करें

प्रकार

रिलीज शीर्षक

नवीनतम संस्करण

एसोसिएटेड उत्पाद

डाउनलोड

फर्मवेयर
1.1.9

These release notes cover the following models:

  • MXW6/8
  • MXWANI4/8
  • MXWAPT4/8
  • MXWNCS4/8

NEW FEATURES

  • Initial Release

KNOWN ISSUES

  • MXW1, MXW2 are not supported in 1.1.9
  • Users may see large fluctuations in Battery time while in Standby Mode
  • GUI connectivity issues may arrise with systems that have been powered on and running continuously for ~20 consecutive days. Power-cycle the system to reinitialize communication. Audio and RF performance are not affected.

NOTES

  • For operation of MXW devices with other Shure networked systems, see the following list of minimum software and firmware versions that are supported with MXW version 1.1.9:
    • SCM820-DAN 1.0.11
    • Shure Web Device Discovery 1.0.8
फर्मवेयर
1.1.9

These release notes cover the following models:

  • MXW6/8
  • MXWANI4/8
  • MXWAPT4/8
  • MXWNCS4/8

NEW FEATURES

  • Initial Release

KNOWN ISSUES

  • MXW1, MXW2 are not supported in 1.1.9
  • Users may see large fluctuations in Battery time while in Standby Mode
  • GUI connectivity issues may arrise with systems that have been powered on and running continuously for ~20 consecutive days. Power-cycle the system to reinitialize communication. Audio and RF performance are not affected.

NOTES

  • For operation of MXW devices with other Shure networked systems, see the following list of minimum software and firmware versions that are supported with MXW version 1.1.9:
    • SCM820-DAN 1.0.11
    • Shure Web Device Discovery 1.0.8
फर्मवेयर
1.3.6

New Features

  • Transmitter "Mute Mode"
    • A mode that changes the functionality of transmitter power switch from "power on/off" to "mute on/off". This feature is enabled/disabled through the transmitter menu, within the UTILITIES section of the menu structure. This functionality as also been added to the IR PRESETS list.
    • Transmitters will communicate via the side channel when/if Mute Mode has been engaged (displayed in Wireless Workbench) and when/if the transmitter has been muted (displayed in Wireless Workbench and the receiver).

Improvements

  • Added support for the X51 frequency band for use in Korea
  • Minor UI text changes for consistency across wireless lines and in Wireless Workbench.

Notes

  • After updating a ULX-D transmitter from any firmware version to 1.3.6, the transmitter will factory reset itself automatically.
  • For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 1.3.6:
    • ULXD1/2 ULXD Transmitters 1.3.6
    • ULXD4, ULXD4D, ULXD4Q ULX-D Receivers 1.3.6
    • AXT400 Axient Receiver 1.10.2
    • Wireless Workbench 6 Beta version 6.6.1
फर्मवेयर
1.3.6

New Features

  • Receiver Mute
    • Previously, receiver channels could be muted from Wireless Workbench amd not on device. Mute on/off capability has been added to the device within the AUDIO menu. Receiver mute for a channel can also be disengaged via a two-button combination push of the up/down gain arrows of that channel.
    • When "Rx Mute" has been engaged, the ability to adjust system gain is disabled. Receiver channels must be unmuted in order to adjust system gain.
    • Muting of a receiver channel is non-persistent (i.e. all channels with "Rx Mute" engaged will no longer be muted after the device is power-cycled).
  • Device Gateway Address
    • ULX-D receiver's gateway address can now be set to allow for cross-subnet control and monitoring of the receiver with 3rd party control surfaces.
    • NOTE: Wireless Workbench does not function across different subnets. This feature is for 3rd party control surfaces only.
  • Hardware Identification in Wireless Workbench
    • Enables the user to trigger a flashing sequence from the physical device to locate the Wireless Workbench representation of that device in the software.

Improvements

  • Added support for the X51 frequency band for use in Korea
  • Minor UI text changes for consistency across wireless lines and in Wireless Workbench.

Known Issues

  • To ensure proper functionality of the device, users must perform a factory reset of ULX-D receivers if any of the following scenarios describe the receiver:
    • The receiver will be updated from 1.0.7 to 1.2.14
    • The receiver will be updated from 1.0.7 to 1.3.6
    • The receiver will be updated from 1.0.7 to 1.2.14 to 1.3.6 - ONLY if no factory reset was performed after updating to 1.2.14

Notes

  • For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 1.3.6:
    • ULXD1/2 ULXD Transmitters 1.3.6
    • ULXD4, ULXD4D, ULXD4Q ULX-D Receivers 1.3.6
    • AXT400 Axient Receiver 1.10.2
    • Wireless Workbench 6 Beta version 6.6.1
फर्मवेयर
1.3.6

Important

  • ULXD4D and ULXD4Q receivers running firmware prior to 1.4.8 must be updated to 1.4.8 before updating to newer versions.
  • ULXD4D and ULXD4Q receivers running firmware between 1.4.8 and 2.0.28 must be updated to 2.0.28 before updating to newer versions.
  • After 2.0.28 is installed, ULXD4D and ULXD4Q receivers can be updated to the latest available firmware version.
  • ULX-D devices that are downgrading to 1.5.6 may report a false failure.
    • Workaround: Because this is a false failure, closing the send updates window and going to the main page, Shure Update Utility will show green for the firmware version.

New Features

  • Addition of Dante Device ID modes
    • ID Mode: Sequential - Quick sequential numbering of ULX-D receivers to take advantage of quick device set-up and labeling for Dante digital audio network.
    • ID Mode: Yamaha - specific labeling of ULX-D receiver's Dante Device ID for discovery as "online devices" by Yamaha CL Series consoles with firmware version 1.60 or later.
  • Receiver Mute
    • Previously, receiver channels could be muted from Wireless Workbench amd not on device. Mute on/off capability has been added to the device within the AUDIO menu. Receiver mute for a channel can also be disengaged via a two-button combination push of the up/down gain arrows of that channel.
    • When "Rx Mute" has been engaged, the ability to adjust system gain is disabled. Receiver channels must be unmuted in order to adjust system gain.
    • Muting of a receiver channel is non-persistent (i.e. all channels with "Rx Mute" engaged will no longer be muted after the device is power-cycled).
  • Device Gateway Address
    • ULX-D receiver's gateway address can now be set to allow for cross-subnet control and monitoring of the receiver with 3rd party control surfaces.
    • NOTE: Wireless Workbench does not function across different subnets. This feature is for 3rd party control surfaces only.
  • Hardware Identification in Wireless Workbench
    • Enables the user to trigger a flashing sequence from the physical device to locate the Wireless Workbench representation of that device in the software.

Improvements

  • Added support for the X51 frequency band for use in Korea
  • Minor UI text changes for consistency across wireless lines and in Wireless Workbench.

Notes

  • For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 1.3.6:
    • ULXD1/2 ULXD Transmitters 1.3.6
    • ULXD4, ULXD4D, ULXD4Q ULX-D Receivers 1.3.6
    • AXT400 Axient Receiver 1.10.2
    • Wireless Workbench 6 Beta version 6.6.1
फर्मवेयर
1.3.6

Important

  • ULXD4D and ULXD4Q receivers running firmware prior to 1.4.8 must be updated to 1.4.8 before updating to newer versions.
  • ULXD4D and ULXD4Q receivers running firmware between 1.4.8 and 2.0.28 must be updated to 2.0.28 before updating to newer versions.
  • After 2.0.28 is installed, ULXD4D and ULXD4Q receivers can be updated to the latest available firmware version.
  • ULX-D devices that are downgrading to 1.5.6 may report a false failure.
    • Workaround: Because this is a false failure, closing the send updates window and going to the main page, Shure Update Utility will show green for the firmware version.

New Features

  • Addition of Dante Device ID modes
    • ID Mode: Sequential - Quick sequential numbering of ULX-D receivers to take advantage of quick device set-up and labeling for Dante digital audio network.
    • ID Mode: Yamaha - specific labeling of ULX-D receiver's Dante Device ID for discovery as "online devices" by Yamaha CL Series consoles with firmware version 1.60 or later.
  • Receiver Mute
    • Previously, receiver channels could be muted from Wireless Workbench amd not on device. Mute on/off capability has been added to the device within the AUDIO menu. Receiver mute for a channel can also be disengaged via a two-button combination push of the up/down gain arrows of that channel.
    • When "Rx Mute" has been engaged, the ability to adjust system gain is disabled. Receiver channels must be unmuted in order to adjust system gain.
    • Muting of a receiver channel is non-persistent (i.e. all channels with "Rx Mute" engaged will no longer be muted after the device is power-cycled).
  • Device Gateway Address
    • ULX-D receiver's gateway address can now be set to allow for cross-subnet control and monitoring of the receiver with 3rd party control surfaces.
    • NOTE: Wireless Workbench does not function across different subnets. This feature is for 3rd party control surfaces only.
  • Hardware Identification in Wireless Workbench
    • Enables the user to trigger a flashing sequence from the physical device to locate the Wireless Workbench representation of that device in the software.

Improvements

  • Added support for the X51 frequency band for use in Korea
  • Minor UI text changes for consistency across wireless lines and in Wireless Workbench.

Notes

  • For operation of ULX-D devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with ULX-D version 1.3.6:
    • ULXD1/2 ULXD Transmitters 1.3.6
    • ULXD4, ULXD4D, ULXD4Q ULX-D Receivers 1.3.6
    • AXT400 Axient Receiver 1.10.2
    • Wireless Workbench 6 Beta version 6.6.1
फर्मवेयर
1.13.5

Release Date: 7/15/2013

NOTES

  • For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.12.8:
    • UR4 UHF-R receiver 1.166
    • UR3 Plug-on Transmitter 1.0.0.9
    • UR5 Portable Diversity Receiver 1.0.0.13
    • ULXD4 ULXD Receiver 1.2.14
    • P10T PSM1000 Transmitter 1.3.4
    • Wireless Workbench 6 Beta version 6.8.0
फर्मवेयर
1.13.5

NOTES

  • For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.12.8:
    • UR4 UHF-R receiver 1.166
    • UR3 Plug-on Transmitter 1.0.0.9
    • UR5 Portable Diversity Receiver 1.0.0.13
    • ULXD4 ULXD Receiver 1.2.14
    • P10T PSM1000 Transmitter 1.3.4
    • Wireless Workbench 6 Beta version 6.8.0
फर्मवेयर
1.13.5

IMPROVEMENTS

  • Supports ULX-D frequency band X51
  • Supports PSM1000 band X7

NOTES

  • For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.12.8:
    • UR4 UHF-R receiver 1.166
    • UR3 Plug-on Transmitter 1.0.0.9
    • UR5 Portable Diversity Receiver 1.0.0.13
    • ULXD4x ULXD Receivers 1.2.14
    • P10T PSM1000 Transmitter 1.3.4
    • Wireless Workbench 6 Beta version 6.8.0
फर्मवेयर
1.13.5

NEW FEATURES

  • Added new TV format option
    • The TV format is titled ‘6 MHz Japan’ and can be selected among other TV formats (6 MHz, 7 MHz, 8 MHz).
    • The new TV format starts at channel 13 and ends at channel 52, each channel with a 6 MHz bandwidth.
  • 6 MHz Japan TV format can be specified from Wireless Workbench for a Spectrum Manager.
    • The new TV format can be downloaded to a networked Spectrum Manager for frequency coordination through the TV Channels dialog.

IMPROVEMENTS

  • Supports ULX-D frequency bands X51, H50
  • Supports PSM1000 band X7
  • Supports MW4D band X7

KNOWN ISSUES

  • CFL Analysis fails when the Spectrum Manager Exclusions list includes both a frequency range and a single frequency within that range. The Analysis result indicates an Exclusions conflict even though no CFL frequencies fall within the range of defined exclusions.

NOTES

  • For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.12.8:
    • UR4 UHF-R receiver 1.166
    • UR3 Plug-on Transmitter 1.0.0.9
    • UR5 Portable Diversity Receiver 1.0.0.13
    • ULXD4 ULXD Receiver 1.2.14
    • P10T PSM1000 Transmitter 1.3.4
    • Wireless Workbench 6 Beta version 6.8.0