Software & Firmware Archives

NEW FEATURES

• Hardware Identification in WWB6
  • Enables the user to trigger a flashing sequence from the physical device to locate the Wireless Workbench 6 representation of that device in the software.
  • To engage, quickly tap the power button on the transmitter.

IMPROVEMENTS

• AXT400 B receiver supports new transmitter bands including J5HK, G12, and H12

NOTES

• For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.11.14:
  • UR4 UHF-R receiver 1.166
  • UR3 Plug-on Transmitter 1.0.0.9
  • UR5 Portable Diversity Receiver 1.0.0.13
  • ULXD4 ULXD Receiver 1.2.14
  • P10T PSM1000 Transmitter 1.3.4
  • Wireless Workbench 6 Beta version 6.6.0

NEW FEATURES

• Hold Audio Overload indicators on front panel metering
  • Optional feature available in receiver Audio settings. Holds the red LED indicator on after an overload event so that it can be identified on the front panel meters after the condition has ended
  • Residual Overload indicators can be cleared from the front panel with the following key combination: ENTER + AUDIO on the home screen menu for the channel that had an overload.
  • Indicators can also be cleared from WWB6.
• Extended range of receiver Squelch setting, the selectable range is -20 to +10 (previously -10 to +10). Lower settings allow for increased operating range without squelch muting when operating on frequencies with low RF noise.
• Hardware Identification in WWB6
  • Enables the user to trigger a flashing sequence from the physical device to locate the Wireless Workbench 6 representation of that device in the software.
  • To engage, quickly tap the power button on the transmitter.

IMPROVEMENTS

• AXT400 B receiver supports new transmitter bands including J5HK, G12, and H12
• Calibration of front panel display, may optimize contrast on some units

NOTES

• For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.11.14:
  • UR4 UHF-R receiver 1.166
  • UR3 Plug-on Transmitter 1.0.0.9
  • UR5 Portable Diversity Receiver 1.0.0.13
  • ULXD4x ULX-D Receivers 1.2.14
  • P10T PSM1000 Transmitter 1.3.4
  • Wireless Workbench 6 Beta version 6.6.0

NEW FEATURES

• Custom User Groups can be saved to the Spectrum Manager using WWB6.
  • The User Groups can be used to constrain frequency calculations run by the Spectrum Manager such that solutions come from specified ranges and sets of frequencies.
  • Once they are programmed to the device, Custom User Groups can be selected in the front panel menu Util>More>User Group then set List value to ‘Custom’.
• Calculation for ULX-D channels in High Density mode
  • The Spectrum Manager frequency calculations treat these devices as non-Intermod sources. Channels of this type will be considered to not generate transmitter-to-transmitter intermod products among themselves while avoiding intermods from other equipment.
  • Optimizes spectral efficiency of ULX-D High Density mode in mixed applications with other equipment types.
• Hardware Identification in WWB6
  • Enables the user to trigger a flashing sequence from the physical device to locate the Wireless Workbench 6 representation of that device in the software.
  • To engage, quickly tap the power button on the transmitter.

IMPROVEMENTS

• Calibration of front panel display, may optimize contrast on some units

KNOWN ISSUES

• When a frequency list (CFL) which includes entries for ULX-D in High Density mode is deployed from WWB6 to the AXT600 Spectrum Manager there are the following known limitations:
  • The Analyze features accessed from the AXT600 front panel interface cannot perform compatibility analysis
  • The AXT600 frequency calculation tools ‘CFL>New’ and ‘Wizard>Update Freqs’ will not calculate frequencies for ULX-D High Density channels that were offline entries in WWB Inventory at the time of deployment to the Spectrum Manager.
  • Note: The AXT600 does calculate, analyze and deploy frequencies to ULX-D High Density channels that are added via the front panel interface.
• CFL Analysis fails when the Spectrum Manager Exclusions list includes both a frequency range and a single frequency within that range. The Analysis result indicates an Exclusions conflict even though no CFL frequencies fall within the range of defined exclusions.

NOTES

• For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.11.14:
  • UR4 UHF-R receiver 1.166
  • UR3 Plug-on Transmitter 1.0.0.9
  • UR5 Portable Diversity Receiver 1.0.0.13
  • ULXD4 ULXD Receiver 1.2.14
  • P10T PSM1000 Transmitter 1.3.4
  • Wireless Workbench 6 Beta version 6.6.0

NOTES

• For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.11.14:
  • UR4 UHF-R receiver 1.166
  • UR3 Plug-on Transmitter 1.0.0.9
  • UR5 Portable Diversity Receiver 1.0.0.13
  • ULXD4 ULXD Receiver 1.2.14
  • P10T PSM1000 Transmitter 1.3.4
  • Wireless Workbench 6 Beta version 6.6.0

NOTES

• For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.11.14:
  • UR4 UHF-R receiver 1.166
  • UR3 Plug-on Transmitter 1.0.0.9
  • UR5 Portable Diversity Receiver 1.0.0.13
  • ULXD4 ULXD Receiver 1.2.14
  • P10T PSM1000 Transmitter 1.3.4
  • Wireless Workbench 6 Beta version 6.6.0

NOTES

• For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.11.14:
  • UR4 UHF-R receiver 1.166
  • UR3 Plug-on Transmitter 1.0.0.9
  • UR5 Portable Diversity Receiver 1.0.0.13
  • ULXD4 ULXD Receiver 1.2.14
  • P10T PSM1000 Transmitter 1.3.4
  • Wireless Workbench 6 Beta version 6.6.0

Important

V5.8.82 is compatible with Firmware Release 7.2.0 or later only

Bug Fixes

• Voting configuration changed in "Agenda Report" and "Conference Log Report"
• Missing voting result for individuals and groups in report corrected
• Empty Group Speech Time in combination with some language codes corrected
• Other minor bugs corrected

Improvements

• Minor bug fixes

Notes

• For operation of PSM1000 devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with PSM1000 version 1.3.9:
  • Axient devices 1.13.5
  • ULX-D Devices 1.3.6
  • Wireless Workbench 6 beta version 6.8.1
  • Shure Update Utility 2.0.2

NEW FEATURES

• Initial release

NOTES

• For operation of SCM820 with other Shure networked systems, see the following list of minimum firmware versions that are supported with SCM820 version 1.0.11:
  • Microflex Wireless 1.1.9
  • Shure Web Device Discovery 1.0.8

IMPROVEMENTS

• New models for transmitter frequency bands
  • G7C, G19, H18, J12, L20, R16
• AXT400C receiver supports new transmitter frequency band: R16

NOTES

• For operation of Axient devices with other Shure networked systems, see the following list of minimum firmware versions that are supported with Axient version 1.12.8:
  • UR4 UHF-R receiver 1.166
  • UR3 Plug-on Transmitter 1.0.0.9
  • UR5 Portable Diversity Receiver 1.0.0.13
  • ULXD4 ULXD Receiver 1.2.14
  • P10T PSM1000 Transmitter 1.3.4
  • Wireless Workbench 6 Beta version 6.6.1