Archiwum oprogramowania i firmware

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Notes

• User Guide
• Command Strings
• To operate this version of MXN5-C with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• To operate this version of MXN5-C with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • IntelliMix Room 4.2.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA710 6.0.24
  • MXA910 6.0.24
  • MXW 10.0.X
  • P300 6.0.38
  • ULXD4D/4Q 2.8.7
  • SCM820 1.4.3
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Known Issues

• When one Unmute/Mute LED light color is set to White at 100% Brightness while the other Unmute/Mute light is set to Off, it may cause the button to freeze or the device mute state to spontaneously change. Lowering the device LED brightness alleviates this issue.

Notes

• User Guide
• Command Strings
• To operate this version of MXA MUTE with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA710 6.0.24
  • MXA910 6.0.24
  • MXN5-C 6.0.17
  • P300 6.0.38
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Loudspeaker nulling to improve doubletalk suppression performance
• Enhancements to support Designer 6.0.0
• Additional hardware support

Notes

• User Guide
• Command Strings
• To operate this version of MXA902 with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• To operate this version of MXA902 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • IntelliMix Room 4.2.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA710 6.0.24
  • MXA910 6.0.24
  • MXA920 6.0.38
  • MXA901 6.0.39
  • MXN5-C 6.0.17
  • MXA-MUTE 6.0.25
  • P300 6.0.38
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Notes

• User Guide
• Command Strings
• To operate this version of MXA901 with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• To operate this version of MXA901 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • IntelliMix Room 4.2.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA710 6.0.24
  • MXA910 6.0.24
  • MXA920 6.0.38
  • MXA902 6.0.32
  • MXN5-C 6.0.17
  • MXA-MUTE 6.0.25
  • P300 6.0.38
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Known Issues

• The optional ARRAY_HEIGHT_OVERRIDE value sent via command strings must be resent upon power cycle
• If the ARRAY_HEIGHT_OVERRIDE command is used to set a height that is outside the valid range (122-914 cm), the command will not display an error but internally, the value will be rejected from being set
• Acoustic reflections from tables can sometimes be mistaken by the MXA920 as another source/talker location.  The symptom is a second talker location coordinate set in front of and higher than the actual talker.
  • Workaround: Place Coverage Areas to minimize pick-up of table surface reflections
• Channel Names are not set in the initial attempt of ‘push-to-Dante’. Dante interface resets when Device Name is set.
  • Workaround: Channel Names are set on the 2nd attempt
• MXA920 LED does not stay on after a reboot if the light settings are set to Unmute = Blue, Mute = Red. Other light combinations work as expected after reboot.
• When a muted dynamic coverage area is moved when a dedicated coverage area has also been established, the mix output of the MXA920 has low-level audio from outside the dedicated coverage area limits.
  • Workaround: Unmute and Mute the dynamic coverage area after a dynamic coverage area is moved

Notes

• User Guide
• Command Strings
• Note that Talker Position Events are published for talkers in a coverage area regardless of the mute status of the coverage area.  To fully inform camera switching decision logic, subscribe to the Coverage Area Mute Status. See https://pubs.shure.com/command-strings for further information
• To operate this version of MXA920 with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• To operate this version of MXA920 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • IntelliMix Room 4.2.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA710 6.0.24
  • MXA910 6.0.24
  • MXA901 6.0.39
  • MXA902 6.0.32
  • MXN5-C 6.0.17
  • MXA-MUTE 6.0.25
  • P300 6.0.38
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Known Issues

• The optional ARRAY_HEIGHT_OVERRIDE value sent via command strings must be resent upon power cycle
• If the ARRAY_HEIGHT_OVERRIDE command is used to set a height that is outside the valid range (122-914 cm), the command will not display an error but internally, the value will be rejected from being set
• Acoustic reflections from tables can sometimes be mistaken by the MXA920 as another source/talker location.  The symptom is a second talker location coordinate set in front of and higher than the actual talker.
  • Workaround: Place Coverage Areas to minimize pick-up of table surface reflections
• Channel Names are not set in the initial attempt of ‘push-to-Dante’. Dante interface resets when Device Name is set.
  • Workaround: Channel Names are set on the 2nd attempt
• MXA920 LED does not stay on after a reboot if the light settings are set to Unmute = Blue, Mute = Red. Other light combinations work as expected after reboot.
• When a muted dynamic coverage area is moved when a dedicated coverage area has also been established, the mix output of the MXA920 has low-level audio from outside the dedicated coverage area limits.
  • Workaround: Unmute and Mute the dynamic coverage area after a dynamic coverage area is moved

Notes

• User Guide
• Command Strings
• Note that Talker Position Events are published for talkers in a coverage area regardless of the mute status of the coverage area.  To fully inform camera switching decision logic, subscribe to the Coverage Area Mute Status. See https://pubs.shure.com/command-strings for further information
• To operate this version of MXA920 with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• To operate this version of MXA920 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • IntelliMix Room 4.2.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA710 6.0.24
  • MXA910 6.0.24
  • MXA901 6.0.39
  • MXA902 6.0.32
  • MXN5-C 6.0.17
  • MXA-MUTE 6.0.25
  • P300 6.0.38
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Known Issues

• When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported

Notes

• User Guide
• Command Strings
• To operate this version of MXA910 with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• To operate this version of MXA910 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA710 6.0.24
  • MXA920 6.0.38
  • MXA901 6.0.39
  • MXA902 6.0.32
  • MXN5-C 6.0.17
  • MXA-MUTE 6.0.25
  • MXW 10.0.X
  • P300 6.0.38
  • ULXD4D/4Q 2.8.7
  • SCM820 1.4.3
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Notes

• User Guide
• Command Strings
• To operate this version of MXA710 with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• To operate this version of MXA710 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA910 6.0.24
  • MXA920 6.0.38
  • MXA901 6.0.39
  • MXA902 6.0.32
  • MXN5-C 6.0.17
  • MXA-MUTE 6.0.25
  • MXW 10.0.X
  • P300 6.0.38
  • ULXD4D/4Q 2.8.7
  • SCM820 1.4.3
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Notes

• User Guide
• Command Strings
• To operate this version of MXA710 with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• To operate this version of MXA710 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA310 6.0.23
  • MXA910 6.0.24
  • MXA920 6.0.38
  • MXA901 6.0.39
  • MXA902 6.0.32
  • MXN5-C 6.0.17
  • MXA-MUTE 6.0.25
  • MXW 10.0.X
  • P300 6.0.38
  • ULXD4D/4Q 2.8.7
  • SCM820 1.4.3
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17

Improvements

• Enhancements to support Designer 6.0.0
• Additional hardware support

Known Issues

• An 802.1X re-authorization request interrupts a firmware update and causes it to fail
  • Workaround: restarting the update will resolve the problem
• AES67 support is only available on UltimoX hardware
  • MXA310 devices manufactured as of July 2017 are compatible with AES67
• In AES67 mode - Audio does not pass after changing Dante Device name, followed by a reboot
• When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported
• The Mute Control Function command string response is incorrect when using <GET 0 ALL>
  • When using < GET MUTE_CONTROL_FUNC >, the response is as documented.
  • When using < GET 0 ALL >, the response should be mapped as follows:

Notes

• User Guide
• Command Strings
• To operate this version of MXA310 with Dante Controller, reference the following minimum versions:
  • v3.10.2.4 (Windows)
  • v3.10.2.3 (Mac OS X)
• Updating all devices used together to the same firmware version is recommended.
• To operate this version of MXA310 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
  • Designer 6.0.0
  • ANI22/ANI4IN/ANI4OUT 6.0.41
  • ANIUSB 6.0.44
  • MXA710 6.0.24
  • MXA910 6.0.24
  • MXA920 6.0.38
  • MXA901 6.0.39
  • MXA902 6.0.32
  • MXN5-C 6.0.17
  • MXA-MUTE 6.0.25
  • MXW 10.0.X
  • P300 6.0.38
  • SCM820 1.4.3
  • Shure Update Utility 2.8.4
  • Shure Web Device Discovery 1.2.17