Archiwum oprogramowania i firmware

Upgrades and Licenses

• This version is used to upgrade from all previous SW6000 versions, however it cannot be used to upgrade systems using CU 6005, CU 6010 or CU 6011 Central Units
• This version is compatible with SW6000 Software License file v1.7 only
• No new SW6000 license is needed if upgrading from SW6000 v6.0.xxx or later versions
• A new SW6000 license is needed if upgrading from SW6000 v5.8.xxx or previous versions

New Features

CAA

• Agenda item durations added - meeting start time used for agenda item start time
• Added Email field to Participants table
• Vote results tab in Agenda is now available if license SW6000-VOTE is available – dependency is removed from license SW6000-ADV

CUA

• Agenda screen displays start time for agenda items (CUA config dependent)
• Added Agenda Time extension control – enabling ‘Auto Update’ feature - Agenda item start time and start time for subsequent agenda items is updated when the subject is set active first time
• Manual Entered Vote results now support 'Unanimous' voting

Beta support for Pre-request to Speak

• Those features require that two dll's are copied to the "Conference Administrator Application\ImportExport" folder (Newtonsoft.Json.dll WebMeetingIntegration.dll).

CAA

• Agenda – support for pre-meeting speak requests for agenda items

CUA

• Agenda – setting an agenda item active populates the pre-meeting request list for the agenda item

Beta support for MXC products

CAA

• Support for ACR1281U-C1 Dual programmer (programs dual interface cards with NFC/Chip interface and CC 6010 cards with Chip interface)
• Support for ACR1252U-M1 (programs dual interface cards with NFC/Chip interface)

CUI

• Beta support for MXC615/MXC620/MXC630 units

Bug Fixes

This section lists the major bugs, where corrections have been made.

Installer

• Fixed a Customer Reported database upgrade error – Collation error

CUA

• Fixed an error
  • where the Microphone speak button state could get out of sync if a replace unit was done including an open microphone unit
  • where scrolling up/down in a large agenda can end up where the line separating the subjects is not being displayed
  • where using the CAA to change speak priority for a meeting role with no active meeting
  • can cause a CUA exception – displayed in system messages
  • where the Last 5 speakers list should be cleared on conference start/stop
  • where the Group speech time is not updated correctly after pause and resume of a meeting
  • where the Total Seat value displayed can be incorrect. Number of seats in seat table used by a meeting is displayed – technician seat types should be excluded in count
  • where the text color for result values is hardcoded – should be configurable
  • when using the mimic to log in a user, the suggested roles for a selected participant is taken from the participant table – should be taken from participant seat table if a table is used for the meeting. Login pop-up should be centred on mimic – placed on top of CUA if mimic is moved to secondary screen
  • where the name displayed for a participant does not reflect the meeting role if the participant is logged in using a different meeting role from the mimic
  • for a meeting with a participant list, where a participant that’s logged out from the mimic is not added to the ‘Participants not present’ list
  • where a participant in the Microphones Control -> Participant List -> Participant Info is displayed with incorrect show name if the participant has been logged in with a Participant Role other than the default for the participant. Resolution is to only show participant name in Participant Info
  • where a participant in the Microphones Control -> Participant List logged in with no speaking rights are not displayed in this. Same problem when no conference is active for microphone units with no speaking right assigned

CAA

• Fixed an error
  • where deleting all CDA displays can make it impossible to add a new CDA display
  • in the Conference Log report, where the report does not show speaker stop time, if speaker was active at meeting stop
  • where the subject title in Agenda Master/Detail view of agenda is not in sync
  • allowing the user to enter special characters in search field in Labels screen
  • in various screens with filter functionality – [Delete] button must be disabled when the search has no results
  • in Meeting Displays (CDA) where filtering and adding a new CDA display, while filter has no results, can result in a blank entry when filter is removed
  • in Meeting Displays (CDA) where the Update button is not enabled when changing values for numeric controls – e.g. instance
  • in various screens with filter functionality – Support using special characters in filter)
  • in various labels e.g. Delegate (User Type) is changed to Participants (Meeting Role) in speech time configuration
  • where a meeting re-import should not overwrite a stop date configured as future date
  • making the filter to correctly filter on start/stop date of meetings
  • in the Subject Vote Report, where Group sorting must be taken into account
  • in the Conference Units window, where clicking Add Unit after doing a microphone scan results in an error
  • in the Participant Table Window, where using the button [Generate] for the field Login Code, correctly generates a new login code, but entry is not marked as updated and the [Update] and [Cancel] buttons are not enabled

Notes

SW6000 and DCS 6000 Compatibility Chart

*****
UPDATE: February 28, 2019: SystemOn 3.0.1 does not support ULX-D devices on version 2.3.21. These devices will be supported in an upcoming version.

UPDATE: November 7, 2018: SystemOn 3.0.1 supports ULX-D devices updated to version 2.3.4, but does not support new hardware revisions of ULX-D on version 2.3.4.

*****

KNOWN ISSUE

SystemOn 3.0.1 incorrectly warns "Check system requirements, your current firmware version may not be confirmed compatible" for firmware versions that it does not support.

To operate SystemOn 3.0.1 with Shure networked systems, see the following list of supported firmware versions:

• SCM810 1.3.3
• ULX-D 1.7.34 - 2.3.4
  • ULX-D J50A or L50A frequency bands are not supported
  • ULX-D new hardware revisions are not supported
• MXW 4.0.6 – 6.0.3

UPDATE: October 30, 2018: SystemOn 3.0.1 supports MXW version 6.0.3; however, it will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”

To operate SystemOn 3.0.1 with Shure networked systems, see the following list of supported firmware versions:

• SCM820 1.3.3
• ULX-D 1.7.34 - 2.2.24
  • ULX-D J50A or L50A frequency bands are not supported
• MXW 4.0.6 – 6.0.3

UPDATE: June 20, 2018: SystemOn will notify users that ULX-D 2.2.24 may not be compatible; however only ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1.

UPDATE: June 13, 2018:

• SystemOn 3.0.1 supports MXW 5.2.2. However, SystemOn will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.” Please disregard this warning.
• MXW 5.2.2 fixes a previous issue where MXW microphones could take more than one minute to be discovered.
• The improvement made to SystemOn 3.0.1, where the time to report missing devices was increased to 3-4 minutes, may remain 1 minute.

*****

Release Date: 12/18/2017

Improvements

• Compatibility with MXW version 5.1.26
• The time before reporting missing devices has been increased to 3-4 minutes to reduce false notifications

Known Issues

• Discovering MXW microphones may take more than 1 minute
• ULX-D Users may receive duplicate SMS notifications
• Metering quality for a single location with greater than 32 devices
• UTC time and date are displayed on Event Log and Email/SMS notifications.
• Navigating through an Event Log with hundreds of events may be slow or could cause the system to time out.
• For non-English users setting up SMS notifications, the Senders Phone Number field doesn’t show the required (*), but the field is required.
• If a valid license activation ID is applied and fails on the first attempt, retry a second time before calling support.

Notes

• To operate SystemOn 3.0.1 with Shure networked systems, see the following list of supported firmware versions:
  • SCM820 1.3.3
  • ULX-D 1.7.34 - 2.1.16
  • MXW 4.0.6 - 5.1.26
• Please report SystemOn performance issues on any browser to Shure Support.
• For help and troubleshooting, go to the SystemOn User Guide or FAQs

Note

Use this version of Shure Update Utility to update firmware on PSM1000 systems running firmware 1.1.0 or earlier.

Important

To update Shure Update Utility (version 2.4 or earlier) to version 2.4.1, download and re-install from Shure.com/SUU and not through Help > Check for Shure Update Utility updates.

Improvements

• Returned support of Shure Update Utility for 32-bit Windows operating systems. To update Shure Update Utility (versions 2.2.2 or earlier) on a 32-bit Windows system, download version 2.4.1 for 32-bit systems to re-install the software.
• Added support for PSM1000 G62

Known Issues

• 32-Bit Windows
  • Selecting "Help" > "Check for Shure Update Utility updates" will open Shure.com, which offers the latest version of Shure Update Utility to download. Shure Update Utility version 2.4.1 will not automatically detect new versions.
  • To update Shure Update Utility (versions 2.2.2 or earlier) on a 32-bit Windows system, download version 2.4.1 for 32-bit systems to re-install the software. Older versions of Shure Update Utility will not detect new updates of Shure Update Utility that support 32-bit systems.
  • Shure Update Utility version 2.4.1 for 32-bit systems is compatible with Wireless Workbench 6 version 6.12 or earlier.
• Attempts to download ULXD6/8 transmitter firmware to a ULX-D or QLX-D receiver that is not at the minimum firmware version will fail. To update firmware for ULXD6/8 transmitters with ULX-D or QLX-D receivers:
  1. Update receivers to the following minimum versions:
     • ULXD4, ULXD4D, ULXD4Q Receivers 2.1.16
     • QLXD4 Receivers 2.1.5
  2. Using Shure Update Utility, download ULXD6/8 transmitter firmware to the receivers.
  3. Using the FW Update menu on a receiver, update transmitters.
• Microflex Wireless devices running version 1.X firmware must first be updated to version 2.0.5 before being updated to version 3.X or later.

Notes

• Installing Shure Update Utility on Windows will also prompt the installation of a USB driver, which must be installed to support updating USB devices, like GLX-D.
• USB 2.0 Devices
  • KSE1500, SHA900 and GLX-D (USB 2.0 connected devices) must be updated one at a time.
  • USB hubs are not recommended when updating USB 2.0 connected devices. Always connect these devices directly to a USB terminal of the computer running Shure Update Utility.
• Shure Update Utility 2.4.1 for 64-bit systems is compatible with Wireless Workbench 6.12.2 or later.
• Shure Update Utility 2.4.1 for 32-bit systems is compatible with Wireless Workbench 6.12 or earlier.

New Features

• Remotely link primary or secondary Microflex Wireless microphones (requires MXW version 5.1.23 or higher)
• Inventory Summary information on homepage
• Transmitter list shows battery health and linked device information

Improvements

• Added compatibility for ULX-D ULXD1/2/4/4D/4Q version 2.1.16
• Added compatibility for Microflex Wireless version 5.1.23
• Microflex Wireless meters show audio/RF activity (requires MXW devices version 5.1.23 or higher)
• Performance enhancements

Known Issues

• Discovering MXW microphones may take more than 1 minute
• Metering quality for a single location with greater than 32 devices
• UTC time and date are displayed on Event Log and Email/SMS notifications.
• Navigating through an Event Log with hundreds of events may be slow or could cause the system to time out.
• For non-English users setting up SMS notifications, the Senders Phone Number field doesn’t show the required (*), but the field is required.
• If a valid license activation ID is applied and fails on the first attempt, retry a second time before calling support.

Notes

• To operate SystemOn 3.0 with Shure networked systems, see the following list of supported firmware versions:
  • SCM820 1.3.3
  • ULX-D 1.7.34 - 2.1.16
  • MXW 4.0.6 - 5.1.23
• Please report SystemOn performance issues on any browser to Shure Support.
• For help and troubleshooting, go to the SystemOn User Guide or FAQs

*****
UPDATE: June 20, 2018: Designer 3.0 is compatible with MXA910 version 3.0.24
*****

Release Date: 8/11/2017

Initial release

Known Issues

• When importing a Designer preset file into the MXA910 web application, attempts to immediately export that file out of the web application will fail if it's not first loaded and saved to the MXA910
• When importing a Designer preset file into the MXA910 web application using MXA910 release 2.0.8 and earlier, attempts to use the low shelf filter after rebooting the device will fail if the preset file was not saved to one of the preset slots

Notes

• Internet access is required during the installation process
• Designer User Guide
• System Requirements
• Designer 3.0 is compatible with MXA910 version 1.1.3–2.0.19

Improvements

• Added support for updating the following devices:
  • AD and ADX Transmitters
  • AD4D Two-Channel Receiver
  • AD4Q Four-Channel Receiver
  • AD610 Diversity ShowLink Access Point
  • ULXD6/8 Transmitters
  • SBC240/450/840/840M/850 Networked Charging Stations
• Added support for the following new frequency band:
  • QLX-D G62

Known Issues

• Attempts to download ULXD6/8 transmitter firmware to a ULX-D or QLX-D receiver that is not at the minimum firmware version will fail. To update firmware for ULXD6/8 transmitters with ULX-D or QLX-D receivers:
  1. Update receivers to the following minimum versions:
     • ULXD4, ULXD4D, ULXD4Q Receivers 2.1.16
     • QLXD4 Receivers 2.1.5
  2. Using Shure Update Utility, download ULXD6/8 transmitter firmware to the receivers.
  3. Using the FW Update menu on a receiver, update transmitters.
• Microflex Wireless devices running version 1.X firmware must first be updated to version 2.0.5 before being updated to version 3.X or later.

Notes

• Shure Update Utility (SUU) version 2.4 requires 64-bit operating systems. To install SUU on a 32-bit computer, download version 2.2.2: Windows 7, 8, 10 or Mac OS X 10.9 – 10.11
• Installing Shure Update Utility on Windows will also prompt the installation of a USB driver, which must be installed to support updating USB devices, like GLX-D.
• KSE1500, SHA900 and GLX-D (USB 2.0 connected devices) must be updated one at a time.
• USB hubs are not recommended when updating USB 2.0 connected devices. Always connect these devices directly to a USB terminal of the computer running Shure Update Utility.
• Shure Update Utility 2.4 is compatible with Wireless Workbench 6.12.2 or later.

Hotfix

Important

• This version is a hotfix for use in systems with CU 6105, CU 6110 and DIS-CCU Central Units only
• This version cannot be used to upgrade systems using CU 6005, CU 6010 or CU 6011 Central Units
• This version is compatible with SW6000 Software License file v1.7 only
  • If upgrading from SW6000 v6.0.xxx or later, a new SW6000 license is not needed
  • If upgrading from SW6000 v5.8.xxx or earlier, a new SW6000 license is needed

Bug Fixes

CUA

• Fixed an error where Pause / Resume meeting did not restore request list in the correct sorting order
• Fixed an error where Pause / Resume meeting did not restore all entries in the request list

Version 6.5.25

Release Date: 6/23/2017

Feature Release

Important

• This version is a feature release for use in systems with CU 6105, CU 6110 and DIS-CCU Central Units only
• This version cannot be used to upgrade systems using CU 6005, CU 6010 or CU 6011 Central Units
• This version can upgrade SW6000 from all previous SW6000 versions
• This version is compatible with SW6000 Software License file v1.7 only
  • If upgrading from SW6000 v6.0.xxx or later, a new SW6000 license is not needed
  • If upgrading from SW6000 v5.8.xxx or earlier, a new SW6000 license is needed

New Features

• Added speech counter in CUA Microphone and Main display
• Added speech counter configuration in CAA/Participant List Configuration
• Added option to configure the voting mimic icons used in the CDA
• Added configuration option in CAA/Configuration/Voting Configuration
• CAA: Report generation time reduced (all reports)
• CDA: Added command-line option to disable page switching
• CUA: Button configuration for speak button and voting buttons color added in the ‘prjCUA.exe.config’ file

Bug Fixes

CUA

• Fixed an error
  • where Pause / Resume meeting did not restore request list
  • for missing Meeting Role information in CUA after using CAA Conference Unit ‘Replace Unit’
  • where CUA Mimic shows assigned user in the meeting mode: ‘Code On List
  • where the Microphone in ‘Manual + reply’ mode cannot be not removed from request list when turned on from Mimic and Mic. ext. control
  • where the manual timer updates anomaly
  • where a participant cannot re-login
  • where the Meeting Role is not updated properly in CUA when Speaker is set for an agenda subject
  • where the buttons ‘Set agenda status’ do not have their own labels (3 labels)

CAA

• Fixed errors with
  • the agenda, when assigning a speaker to an Agenda Subject in a Meeting
  • Room Configuration. Meeting Role is not being applied to a unit
  • Voting reports - individual participants are listed multiple times each
  • Voting reports - missing some results from proxy delegates
  • participants votes, which are ignoring the use of voting weight
  • Label 507, which is used in some wrong places
  • Participant Table, unable to clear Replacement For …..
  • duplicated user ID in Prepared Participant List
  • printing reports from CUA
  • editing a Participant Seat Table
  • the Participant Seat Table, where participants cannot be moved from one seat to another in the table
  • the language selection menu 'Invariant Language (Invariant Country)
  • an CAA Exception: when adding participants in Meeting Mode: Prepared Participant List
  • importing the ‘Default Participant Table’ to a ‘Prepared Participant Table’

CDA

• Fixed an error
  • with Logged In display: Wrong Group shown for meeting using’ Participants Lists’
  • with Microphone Display: Pause speech timer indicator missing
  • with Microphone Display: Speech time count down timer keeps on blinking, red color does not stop after time has run out or the meeting is stopped
  • with font size in skin editor

CUI

• CUI Fix for Web service exception with very large agenda: Maximum request length exceeded
• ‘Pooltime’ default value changed to 200ms (can also be set in command line). Note: This time shall still be set using CUI command line parameter for customers using automatic login on preferred seat in large system

Reports

• Participant Meeting Report, ID 1243 – Fix for show time for non-participating participants
• Participant Statistical Report - Fix for incorrect if changes occur while CAA is open with active meeting
• Participant Statistical Report - Participant Speech Time is not updated properly
• Meeting Log report – sub repor6t parameters missing Vote report(s) with Groups - missing 'No Group' in Group Voting Result table Meeting Log Report - generation failed (on Russian database)

Installer

• Prevent installing on systems where SQL server version is 2005 or earlier

Improvements

• Added support for Axient Digital receivers and AD series transmitters, including:
  • AD1/2 Bodypack and Handheld Transmitters
  • AD4D Dual Receiver
  • AD4Q Quad Receiver
  • AD610 Diversity ShowLink Access Point
• Added support for the following new devices/bands:
  • ULX-D ULXD6/8 Boundary and Gooseneck Transmitters
  • SBC450/850 Networked Charging Stations (featuring redesigned properties panels)
  • BLX H62
  • PSM300 H62
  • PSM900 G62
  • PSM1000 G62
  • QLX-D G62
  • SLX H62
• Added prompt in Preferences > Coordination to enable User Group for countries that support them

Known Issues

• Installing & Upgrading
  • Version 6.12.2 requires a 64-bit system. To install Wireless Workbench 6 on a 32-bit system, install and run version 6.12.0.88: Windows 7, 8, 10 or Mac OS X 10.9-10.11
  • Windows users attempting to install version 6.12.2 or later may  see an error message mentioning a missing .dll file(s). Users should  contact their computer's Administrator to ensure the computer has the  necessary libraries configured in order to install Wireless Workbench.
  • Checking for Wireless Workbench 6 updates using Shure Update  Utility 2.2.2.8 will not detect new versions of Wireless Workbench.  Download the latest version of Shure Update Utility
  • If you are running the Mac OS X Yosemite Operating System, be sure  to run version 10.10.4 or later. Earlier beta versions of the Operating  System are not supported.
• When connecting to AXT400, AXT610, and AXT transmitters across  subnets (as Remote Devices), ShowLink connectivity between the  transmitter and other components is not fully functional. Linked  transmitter status from the vantage point of the receiver and the Access  Point will show as not connected.
• On Macs, when users open show files and launch the Frequency  Analysis dialog (by checking the checkbox and pressing “Analyze”), the  Frequency Coordination tab may stop responding to keyboard inputs (for  example, editing or deleting frequencies with the keyboard). To work  around this issue, select another tab in the application (e.g.:  Inventory or Monitor) and then reselect the Frequency Coordination tab.
• SLX and ULX frequencies in Master List mode cannot be manually  entered in the Coordination Workspace. They can, however, be coordinated  and analyzed.
• When scanning with AXT400 receivers, the Band Preset value in the  Live Scan Settings dialog does not always stay in sync with the  currently selected band of the receiver. The Band Preset can be manually  changed to scan any supported range.
• Alerts logged when devices first come online may list device  parameters and their values as they are being discovered even though the  parameter values themselves have not changed.

Notes

• Tags that have been added to a show file, but are not assigned to any devices, are not saved within the show file.
• Opening show files created with older versions of Wireless  Workbench may result in the Settings Conflicts dialog opening once the  file has loaded, which is due to newly supported hardware parameters  that have been introduced with updated firmware versions. To maintain  all settings from the show file, select "Keep all settings from:  Wireless Workbench".
• On machines running Windows 7, Wireless Workbench will not discover  devices when the machine has fallen back to its 169.254.xxx.yyy  fallback IP address, regardless of the IP addresses of the connected  Shure devices. To resolve this, perform one of the following:
  • Insert a DHCP server onto your network and set your machine and Shure devices to accept automatic IP addresses.
  • Statically assign your machine's IP address to the 169.254.xxx.yyy  fallback subnet with a different IP address than the one it fell back  to originally.

Improvements

• Support for ANI22, ANIUSB-MATRIX, and IntelliMix® P300
• If a supported device supports both Dante and AES67, then the Network Audio column will display "Dante / AES67"
• macOS Sierra (version 10.12) compatibility
• Bug fixes

Known Issue

• Windows 10 users who are using the Microsoft Edge browser can only use the Open by IP preference to discover devices and launch web-based user interfaces.

Notes

• The software is supported on the following operating systems:
  • Windows: 7, 8, 10
  • Mac: OS X 10.10-10.12
• The software is compatible with the following systems:
  • Audio Network Interfaces
  • IntelliMix® P300
  • Microflex® Advance™
  • Microflex® Wireless
  • SCM820

Improvements

• Added support for updating the following devices:
  • IntelliMix® P300 Audio Conferencing Processor
  • ANIUSB-MATRIX
  • ANI22
  • Shure Battery Rack Charger (SBRC)
• Added support for updating the following new bands:
  • ULX-D G62, Z17, Z18, Z19, Z20
  • QLX-D Z17, Z18, Z19, Z20
• macOS Sierra (10.12) compatibility

Known Issues

• Microflex Wireless devices running version 1.X firmware must first be updated to version 2.0.5 before being updated to version 3.X or later.

Notes

• Shure Update Utility (SUU) version 2.3 requires 64-bit operating systems. To install SUU on a 32-bit computer, download version 2.2.2.8: Windows 7, 8, 10 or Mac OS X 10.9 – 10.11
• KSE1500, SHA900 and GLX-D (USB 2.0 connected devices) must be updated one at a time.
• Installing the Shure Update Utility on Windows machines will prompt the installation of a USB driver in addition to the original application. This driver must be installed to support updating USB devices, like GLX-D.
• The use of USB hubs is not recommended when performing updates to GLX-D devices. Always connect a GLX-D device directly to a USB terminal of the computer running the Shure Update Utility.
• Shure Update Utility 2.3 is compatible with the following software:
  • Wireless Workbench 6.12